The perfect way to treat that extra special modeller.

Our gift cards will be delivered immediately via email and can be redeemed as soon as it arrives. The gift card never expires and should the purchase be smaller than the gift card. The remaining amount will be left on the gift card ready for their next purchase. You can also create a custom amount by purchasing multiple gift cards.

Infini-Model, Sanding Monster Bundle. We put together this monster bundle to give you all the sanders you’ll ever need for every occasion, no matter what you build. This bundle includes one of each of all the Infini-Model sanding starter packs, for a whopping total of 45 sanders.

1X Softback Sanding Sticks Full Set 

1X Matador Soft Sanding Sticks Full Set

1X Matador Sanding Sheets Full Set with PE Sanding Tool

1X Zebra Sanding Sticks Full Set

1X Elastic Sanding Film Full Set

1X Softback Sanding Sponges Full Set

Complete set of 8 Infini-Model, Matador premium soft sanding sticks.

Set contains 1 each of 400, 600, 800, 1000, 2000, 3000, 5000 & 7000 grits (8 sticks total).

Manufactured using waterproof sanding sheets by Matador, Germany. 

Eight doubled sided sticks per pack, can be used wet or dry. Each stick measures 133mm x 18mm x 3mm

Complete set of 8 Infini Model, Matador Sanding Sheets and PE Sanding Holder Tool.

Set contains 1 each of 400, 600, 800, 1000, 2000, 3000 5000 and 7000 grits (8 sheets total) plus the PE sanding tool.

Eight sheets per pack, can be used wet or dry. Each sheet measures 225mm x 90mm.

HiQ Parts brings us the perfect tool for applying water-slide decals! 

The Decal Squeegee is designed to remove water from under decals, wiping off the wet surface around the decal, holding down decals and wiping off unnecessary glue after drying.

The sponge is made of resin with added hydrophilicity. It's a soft material and features a round surface rather than a point, so it's easy to apply pressure evenly across the decals. Additionally, it can easily be used when working with the curved surfaces of your model kits, so it's great for large decals that wrap-around edges. The shaft is made from high-quality aluminium, making it easy to rotate between your fingers when working.

How to use:  Roll the sponge across the surface of your kit before the attached decal dries to remove any moisture from under the decal. Squeeze the sponge and dry it on a cloth between uses, to keep it working at its best.

Please note: The sponge is a disposable item. Replace if necessary when it no longer absorbs water. Replacement sponges are available. After use, please wipe off all moisture from both the sponge and shaft and allow to dry. Mould and bacteria may occur if left wet.

Size: Sponge part: 7.8mm in diameter, total length: 123mm

Made in Japan

HIQ Parts Scribing Guide Tape is a thick solid tape that easily conforms to curves and bends and is ideal for all those tricky scribing jobs. Rubs down and lifts off easily without leaving residue on your model. 

This bundle includes both 3mm and 6mm rolls each 30 meters long.

HIQ Parts, Painting Clip

An all-metal high-quality painting clip. That feels very rigid and helps improve fine handling when painting, such as rotation and tilting with your fingertips. When it gets dirty it can be cleaned with thinners. It can also be used as a handle for parts during sandblasting.

156 mm long, 20 all-metal clips per pack.

Our Micro Set and Sol holder beautiful holds your favourite decal solutions to stop them from tipping or be knocked over. Our holder features 3 compartments for different size and type of cotton buds, 4 holes for brushes and 2 slots to hold your decal tweezers. Keeping all of your decal equipment together where you need. Also designed into our holder is a unique lid support so you’ll always know where the lids are and never get them mixed up.

3D printed from PLA in putty grey. There may be some small imperfections as these are 3D-printed products. Fitment is not guaranteed.

(Does NOT include Micro Set, Sol & other accessories)

No longer fear about destroying your cutting mat, instruction book, decals or lungs with our 3D printed cement holders.

Our Tamiya Cement holder has been specially designed to stop the bottles from tipping over. The bottles sit very sung inside the holder avoiding any wobbling when installed. Their strong and stable enough to stop most accidental knocks or flicks of the bottle, making them a cutting mat saver. 3D printed from PLA in a range of colours.

3D printed from PLA in putty grey. There may be some small imperfections as these are 3D-printed products. Fitment is not guaranteed.

(Does NOT include Tamiya Cement)

One each of all the Mr Hobby, Mr Metal Colors, 9 colours total.

Mr Hobby has discontinued this range, sold out colours will not be stocked. A replacement range will be released later this year.

Mr Metal Color is a lacquer based metalizer. Which can be brush painted or airbrushed, use Mr Color or Mr Rapid thinner for thinning (Do not us levelling thinner as the decreased drying time will allow the metal particles to sink to the bottom creating a duller finish.) Once dry in around 10 minutes Mr Metal Color can be buffed with a soft cloth, cotton buds or a microfiber cloth for an ultra-realistic metal finish and shin.

9X 10ml Bottles